Thermo Scientific Incubator co2 300 micro Queue Stabiltherm Lab SNW300TABB

Description

FREE FREIGHT TO A COMMERCIAL ADDRESS WITH A LOADING DOCK IN MIAMI FLORIDA.
Queue Stabiltherm Lab Oven Cabinet Model SNW300TABB
Thermo Scientific Incubator co2 300 micro
These incubators are designed to create a stable, reliable environment for cell culture applications.
They operate at temperatures ranging from 5°C above ambient temperature to +60°C, accurate to ±0.2°C.
The gas system controls within ±0.1% of measurable setpoint.
• Thermal conductivity Sensor. Provides stable, automatic injection of CO2
• Optional Tank Interchange System: – Allows the interconnection of multiple gas supply cylinders for extended operation. – Control panel warning system signals when one of the gas supply cylinders is empty. – Automatically switches from the empty cylinder to the full cylinder. • Convenience Outlet. A receptacle rated at 115 VAC, 75 watts maximum, is located at the rear of the incubator. The outlet is ideal for electronic recorders or other small loads. Do not exceed the electrical capacity of this outlet.
• Automatic Gas Shutoff. Incubator controls shut off the gas supply when the inner glass door is opened to prevent wasting the control gas. •   Alarms: – High and low level CO2 setpoint alarms, fixed at ±1%. – High and low temperature alarms. The high alarm can be set by the user. • Chamber Drain. Seamless tank models are provided with a chamber drain fitting at the bottom left side of the cabinet.
• Humidity Diffuser. For models with humidity pans, a pan cover diffuses evaporation, optimizing the humidity level.
• Optional HEPA filter. Available for all models, HEPA filters remove airborne particulates from the chamber. 1.2 Requirements • A high quality two-stage, low pressure 15 psig (1.056 kg/cm2 ) pressure regulator is required for proper operation of the CO2 gas supply. • In-line gas supply filters must be used on the CO2 supply to prevent damage to the solenoid valve(s): – Type: Microbiological – Specification: 0.3 micron – Location: rear of unit
• CO2 used in the incubator must be at least 99.9% pure. • Each chamber contains approximately 12 gallons of jacket water when filled (water-jacketed models only). The water takes six to eight hours to heat from 20° to 37°C. This time must be allowed for the interior temperature to stabilize before any adjustments or permanent calibrations are made.
1.3 Specifications Gas Control Type Thermal Conductivity. Control Sensor Matched Thermistors. Control Setpoint Direct digital, 0 to 20% range. Control Accuracy ±0.1% of setpoint. Recovery Automatic, actuated by inner door opening. Recovery Time Less than eight minutes at 5% setpoint. Filter Disposable, autoclavable for each input. Hi/Lo CO2 Alarms Audio and visual at ±1.0% setpoint deviation. Low alarm has 15 minute delay after inner door opening. Alarm Silence Touchpad on control panel, 15 minute ringback. Minimum grade CO2 99.9% purity Temperature Control System Range 5°C above ambient to +60°C. Accuracy ±0.1°C Safety Alarms Monitor the chamber temperature, independently adjustable within 0.3°C of setpoint. Audible and visual warnings. Alarm silence has a 15 minute ringback. Display LED, digital, 0.1°C resolution, independent probe. Humidification Range When humidity pan cover is in place and water reservoir is properly maintained, humidity is approximately 96% at 37oC. Construction Welded Tank Models Stainless steel interior, baked-on powder coated exterior. Seamless Tank Models Stainless steel or copper lined interior, baked-on powder coated exterior. Walls Triple Construction for water-jacketed models only. Additional insulation around water jacket provides protection against large ambient temperature fluctuations. Double Construction for dry wall models only. Inner Door Contamination resistant silicone rubber gasket seals against tempered glass. Positive latch. Outer Door Flush mounted with heater on inner surface to provide radiant heat to inner glass door to minimize condensation. Leveling Feet Adjustable, non-skid design. Placement of feet allows mounting on 24 in. (61 cm) deep laboratory bench. Utilities CO2 Connections Automatic tank switching (optional): two 3/16 in. D (4.76 mm) tubing connections. One tank units: one 3/16 in. D (4.76 mm) tubing connection. CO2 Input Pressure 10 to 15 psig (0.7 to 1.06 kg/cm2) required. One two-stage, 15 psig pressure regulator for each cylinder. Electrical Requirementsa a Both domestic and export units utilize 115/1/60 or 220/1/50 or 60. Single Units: • Domestic 115 VAC, 50/60 Hz, one-phase, 4.0 amps and 220 VAC, 60 Hz, one-phase. 15 amp dedicated circuit recommended. • Export 220 VAC, 50/60 Hz, one-phase, 2.0 amps and 115 VAC, 60 Hz, one-phase. 10 amp dedicated circuit recommended. Dual Units: • Domestic 115 VAC, 50/60 Hz, one-phase, 7.4 amps and 220 VAC, 60 Hz, one-phase. 15 amp dedicated circuit recommended. • Export 220 VAC, 50/60 Hz, one-phase, 3.7 amps and 115 VAC, 60 Hz, one-phase. 10 amp dedicated circuit recommended. Water Jacket Fill and Drain Fill: Top of chamber, plastic, snap-on cover. Drain: Snap-on locking fitting (seamless tank models only).
Construction Stainless steel, perforated, precision flat, with adjustable shelf brackets to prevent tipping. Shelves, brackets, and supports are removable without tools for cleaning, chamber decontamination, and maintenance. Capacity Welded Tank: • 24 maximum quantity (four included with unit) • Area is 47.5 ft2 (4.41 m2) • Clearance is 3/4 in. (19 mm) Seamless Tank: • 20 maximum quantity (five included with unit) • Area is 40.8 ft2 (3.8 m2) • Clearance is 3/4 in. (19 mm) Dimensions Welded Tank Single Unit: 25.4 in. (64.5 cm) wide 40.7 in. (103.4 cm) high 23.5 in. (59.7 cm) deep Dual Unit, Stacked: 25.4 in. (64.5 cm) wide 79.4 in. (191.7 cm) high 23.5 in. (59.7 cm) deep Working Interior: 20 in. (50.8 cm) wide 28 in. (71.1 cm) high 18 in. (45.7 cm) deep Shelf: 17.5 in. x 18.5 in. Seamless Tank Single Unit: 25.4 in. (64.5 cm) wide 40.7 in. (103.4 cm) high 23.5 in. (59.7 cm) deep Dual Unit, Stacked: 25.4 in. (64.5 cm) wide 79.4 in. (191.7 cm) high 23.5 in. (59.7 cm) deep Working Interior: 20 in. (50.8 cm) wide 28 in. (71.1 cm) high 18 in. (45.7 cm) deep Shelf: 17.5 in. x 18.5 in.